- a -

• aB : appUserOutputs.h
• Ab : appUserOutputs.h
• Ac : appUserOutputs.h
• aC : appUserOutputs.h
• ADC_SAMPLE_EVERY_10_PWM : measure.h
• ADC_SAMPLE_EVERY_11_PWM : measure.h
• ADC_SAMPLE_EVERY_12_PWM : measure.h
• ADC_SAMPLE_EVERY_13_PWM : measure.h
• ADC_SAMPLE_EVERY_14_PWM : measure.h
• ADC_SAMPLE_EVERY_15_PWM : measure.h
• ADC_SAMPLE_EVERY_16_PWM : measure.h
• ADC_SAMPLE_EVERY_2_PWM : measure.h
• ADC_SAMPLE_EVERY_3_PWM : measure.h
• ADC_SAMPLE_EVERY_4_PWM : measure.h
• ADC_SAMPLE_EVERY_5_PWM : measure.h
• ADC_SAMPLE_EVERY_6_PWM : measure.h
• ADC_SAMPLE_EVERY_7_PWM : measure.h
• ADC_SAMPLE_EVERY_8_PWM : measure.h
• ADC_SAMPLE_EVERY_9_PWM : measure.h
• ADC_SAMPLE_EVERY_PWM : measure.h

- b -

• bC : appUserOutputs.h
• Bc : appUserOutputs.h

- c -

• COMPUTE_OFFSET : measure.h
• CURRENT_INVALID : measure.h
• CURRENT_SINGLE_SHUNT : measure.h
• CURRENT_THREE_SHUNT_A_BC : measure.h
• CURRENT_THREE_SHUNT_AB_C : measure.h
• CURRENT_THREE_SHUNT_DYNAMIC : measure.h
• CURRENT_TWO_SHUNT_A_B : measure.h
• CURRENT_TWO_SHUNT_A_C : measure.h
• CURRENT_TWO_SHUNT_B_C : measure.h

- e -

• ERROR_ADDR_RANGE : uart_comm.h
• ERROR_MISMATCH_CRC : uart_comm.h
• ERROR_MISMATCH_END_BYTE : uart_comm.h
• ERROR_MISMATCH_START_BYTE : uart_comm.h
• ERROR_MISMATCH_TARGET_ADDR : uart_comm.h
• ERROR_NONE : uart_comm.h

- f -

• FAULT_HARDWARE_OVER_CURRENT : appUserOutputs.h
• FAULT_HV_DIE : appUserOutputs.h
• FAULT_LOAD_STALL : appUserOutputs.h
• FAULT_MOTOR_STALL : appUserOutputs.h
• FAULT_NONE : appUserOutputs.h
• FAULT_VOLTAGE_OUT_OF_BOUNDS : appUserOutputs.h

- i -

• IPD_IDENTIFIED_SECTOR_MAX : appUserOutputs.h

- m -

• MEASURE_PHASE_CURRENT : measure.h
• MEASURE_PHASE_VOLTAGE : measure.h
• MOTOR_ALIGN : appUserOutputs.h
• MOTOR_BRAKE_ON_START : appUserOutputs.h
• MOTOR_BRAKE_ON_STOP : appUserOutputs.h
• MOTOR_CLOSE_LOOP_ACTIVE_BRAKING : appUserOutputs.h
• MOTOR_CLOSE_LOOP_ALIGNED : appUserOutputs.h
• MOTOR_CLOSE_LOOP_UNALIGNED : appUserOutputs.h
• MOTOR_FAULT : appUserOutputs.h
• MOTOR_IDLE : appUserOutputs.h
• MOTOR_IPD : appUserOutputs.h
• MOTOR_ISD : appUserOutputs.h
• MOTOR_MAX : appUserOutputs.h
• MOTOR_OPEN_LOOP : appUserOutputs.h
• MOTOR_SLOW_FIRST_CYCLE : appUserOutputs.h
• MOTOR_SOFT_STOP : appUserOutputs.h
• MOTOR_START_ALIGN_AND_GO : appUserInputs.h
• MOTOR_START_DOUBLE_ALIGN : appUserInputs.h
• MOTOR_START_IPD : appUserInputs.h
• MOTOR_START_SLOW_FIRST_CYCLE : appUserInputs.h
• MOTOR_STOP_ACTIVE_SPIN_DOWN : appUserInputs.h
• MOTOR_STOP_HARD_STOP : appUserInputs.h
• MOTOR_STOP_HI_Z : appUserInputs.h
• MOTOR_TRISTATE : appUserOutputs.h

- n -

• NO_FAULTS : appUserOutputs.h

- o -

• OFFSET_COMPLETE : measure.h
• OFFSET_INIT : measure.h

- p -

• PHASE_A : mcLib.h
• PHASE_B : mcLib.h
• PHASE_C : mcLib.h
• PHASE_INVALID : mcLib.h

- s -

• SECTOR_1 : mcLib.h
• SECTOR_2 : mcLib.h
• SECTOR_3 : mcLib.h
• SECTOR_4 : mcLib.h
• SECTOR_5 : mcLib.h
• SECTOR_6 : mcLib.h
• SECTOR_INVALID : mcLib.h
• SVM_CONTINUOUS : mcLib.h
• SVM_DISCONTINUOUS : mcLib.h

- u -

• UART_STATUS_IDLE : uart_comm.h
• UART_STATUS_PROCESS_FRAME : uart_comm.h
• UART_STATUS_RX_BUFFERING : uart_comm.h
• UART_STATUS_TX_TRANSMITTING : uart_comm.h

- v -

• VOLTAGE_GAIN_VMAX_BY_1 : measure.h
• VOLTAGE_GAIN_VMAX_BY_2 : measure.h
• VOLTAGE_GAIN_VMAX_BY_4 : measure.h
• VOLTAGE_VECTOR_AB : focHALInterface.h
• VOLTAGE_VECTOR_AC : focHALInterface.h
• VOLTAGE_VECTOR_BA : focHALInterface.h
• VOLTAGE_VECTOR_BC : focHALInterface.h
• VOLTAGE_VECTOR_CA : focHALInterface.h
• VOLTAGE_VECTOR_CB : focHALInterface.h
• VOLTAGE_VECTOR_MAX : focHALInterface.h